House Painting

The weather was so nice outside yesterday that I decided to go out and work on finishing up the house painting. You may remember that I began painting the house back in May.

I got the right front side done and most of the left side.



I still have to finish the Porch, the back 2nd floor of the house, the left side kitchen, and the right side laundry room.

2nd floor porch, new front door.

Work has been progressing slowly but I have gotten some work done. I finally finished rebuilding the second floor porch. There were two very small areas that were leaking but they were letting a ton of water in. This has caused some of the beadboard on the first floor porch ceiling to come off. Great, another project.



While I was fixing the leaks I made a design change that had been bothering me ever since I first built it. In the picture below notice the 2x4's running left to right, they are what the decking attaches to:


Notice anything wrong with this setup? There's nowhere for the water to drain! It will get between the floor boards then be trapped behind the 2x4's. I don't know what I was thinking when I did this. It's a really stupid mistake. This wasn't what caused the leak but water would have pooled and eventually caused rot.

The way I fixed this was to pull up the 2x4's, take some 6' fence panels and rip them in half lengthwise to make 8 6'x3"x3/4" pieces, then lay them front to back. Then I placed the 2x4's on top of them. Now the water can drain. Sorry I didn't get a picture of it but I think I described it clearly.

Anyways, while I had the 2x4's up I took the time to add another layer of some heavy duty roof cement to the sub floor. I also used a ton of roofing caulk wherever I thought it might be a possible leak area. We got a good bit of rain the next day after I did this and no leaks!

I went ahead and primered and painted the railings before I reinstalled them since it's much easier that way. Here's a few shots of the completed second floor porch:




I went out on the porch roof this morning to get these next two pictures without realizing that there was ice on the roof! Of course I didn't slip until I was about 8 steps out and turning around to take the pic. That could have been bad...


One of the things I did a few months back that I never got around to posting is the Dining room mantle. This is how it looked when we first got the place:

This is as far as I got on it last Winter:

I finished scraping the paint off of it then sanded it 3 times with progressively smoother sandpaper. Here it is after the final sanding:

Then I applied 2 coats of amber shellac:


I still have to scrape the paint off the tiles, repair the hearth tiles, and put up oak trim around the hearth (the original was removed for the 70's shag carpet).

We found a beautiful door at a flea market out in Alabama last month. We picked it up for $50! It's a wonderful Victorian door with a purplish glass inset. In the pic below I'm test fitting it into place. I had to trim about 1" off the bottom:

The mortise for the lock was on the wrong side, I would have just hung the door the opposite way but I've already installed all the light switches on the left side of the door. The outside of the door is different so I couldn't just flop the door around. So I had to make a new mortise on the other side of the door and fill in the old one. I took heavy paper towels and packed them in the mortise as hard as I could then used wood putty to fill in the rest.

Cutting out the new mortise by hand was a real pain in the ass! I used a drill bit of the same diameter as the mortise lock and a chisel. Old school... I also had to cut out the area for the hinges and fill in the area where the hinges were.

There were also a lot of small holes where things had been nailed into the door over the years and even a 9" long chunk of the edge that had come off. Also someone had gouged a rough hole in the door for an old doorbell at one point. All this had to be repaired. Once it was repaired I installed the hardware, I used the door hardware off my old door. Here is a shot of the test fit after all this was done:

Then I put on a coat of amber shellac and a coat of satin poly:



I think the wood putty is a bit too noticeable where the old door knob and door bell had been. I may strip those areas, stain the wood putty to match the rest of the door then re-shellac and poly it.

Our latest camper

Once again it's been a long time without a post. Sorry for that folks. I've dont a few things on the house but not really a lot.

I had to go back and tear out the second floor porch I built because there were a few leaks. I've gotten all the leaks under control and am in the process of rebuilding the porch.

we've spent much of our time trying to stay warm. I refuse to reconnect our service with the gas company because they are a bunch of crooks. Up until the other day we only had one space heater for the whole house. Once the temps got into the low 50's in the house I broke down and bought a few more space heaters. Now it is much more comfortable in the house.

In other news we've bought another camper to restore. Some of you may remember the Airstream we restored this past spring that we subsequently sold. Well now we've bought a 1948 Spartan Royal Mansion. it's going to need a ton of work but in the end I think it will be worth it.



There's a lot more pictures on the blog.

Building the second floor deck

I didnt get as much done over the weekend as I'd hoped but progress was still made. Saturday morning I got back to work. First I installed flashing in the deck area:
Once that was secure I installed the beaded wood siding to the porch roof. I still need to add some flashing to the top, I'll cover it with trim:

Next I sealed the tin floor with an aluminum and tar mix that I found in the roofing section of Lowes:

And then installed the 1x6 decking:

The next day I got to work on designing a railing. I had a newel post from the stairs of the old Anderson house, plus the cap to a second newel post. I was able to dig up enough wood and matching trim to build a second post just like the first:


The one on the right is the original, the one on the left is the one I built.

I sanded and primered them and installed them on the deck. I also installed the railing. I have about a dozen spindles left over from the railing I built for the first floor but it wont be enough, I'll have to get some more.

Porch roof progress and Fence pics

Here are a few pics of the completed privacy fence:

This first one gives you an idea of the area I had to work with, not much room between the chain link fence and the tree line:

In the next pic, the neighbors house is on the right, you can see how close to the line their house is:
This last pic was taken from the neighbors yard:

The front porch roof is coming along. I shortened the deck by 2' on either side, I'm really glad I did because it looks a lot better.



In the above two shots I had the framing done but hadn't put the sheathing on the shortened area.

I finished the sheathing then felted it and then put up aluminium flashing in the areas that needed it. Next I started the shingles, the next 2 pics show how far I got yesterday before I ran out of nails and shingles:



Here's how it looks from the street:



Much better than it was.

This afternoon I'll be finishing off the shingling then taking the old wood that I tore off to the dump. Then hopefully I can install the decking and the railing.

Rebuilding the 2nd floor porch

Well it's been another month since I last posted again... Things have been quite busy. Since the last post I've finished up the Airstream and then sold it, and then bought a boat.

That doesn't mean that there hasn't been any work done on the house though. I finally finished up the privacy fence in the back yard but I forgot to upload the pictures to my server so I cant get to them here at work. I'll post a few pictures in my next post. This last area (about 175') was the hardest to do because there are a lot of large old trees right along the property line and of course a 6' chain-link fence right up against where I put the privacy fence.

I know I was supposed to make some follow-up posts on all the other work done but I wasn't happy with the pictures and still haven't gotten around to taking more.

The other big project I've been working on is the second floor porch. This has been an eyesore since day one. We ripped the roof off last month and that helped but the deck was in really bad shape not to mention that it wasn't centered on the house and altered the pitch of the porch roof in front of it.

So this weekend I got to work. First I tore off the old plywood decking. This was pretty tough since they used about 5000 nails to hold it all down. Once the plywood was up there was of course another floor underneath it. this floor was old tongue & groove board:

I pulled up all the board and found another layer underneath. Under all the rotted leaves and dirt is a layer of tin followed by 1x6 boards.

I measured back to the point where I wanted the new deck to end then cut the tin off at that point:

Then I pulled off all the 1x6 boards in the same area:

I then removed the tin, 1x6's and joists from the left side of where the new deck will be:

The next morning I removed the siding from the front of the house and installed the roof trusses:

In the above picture you'll notice the 2x6 floor joists in front of where the deck is, these joists are holding up the deck but they need to be removed to restore the original pitch of the roof. What I did was to run pressure treated 2x6's alongside the old 2x4 ceiling joists then nailed 2x4 support braces between the 2x6 floor joists and the 2x6 pressure treated joists. I was then able to cut down the 2x6's to the length of the deck:

Then I ran the roof trusses in front of the deck:

Then I installed 3/4 plywood sheathing:


Yesterday afternoon I laid the felt down:


We've decided that the new deck is too wide so this afternoon I'm going to shorten it by 2 feet on either side. This shouldn't take too long to do then I can start laying the shingles. I also need to add beadboard to the exposed sides of the roof and of course add aluminum flashing to everything. Once all that is done I need to put down some type of weatherproofing for the deck then install 1x6 decking over it. Then I can install the railing.

Removal of the 2nd floor porch roof

Wow, a month since I posted last! That doesn't mean that there hasnt been any work going on here though. Just the opposite, I've been so busy working on the house that I havent had time to post. I'm going to have to break it all up into a few posts.

We FINALLY tackled the long awaited the 2nd floor porch roof demo! Here are a few pics of the work from a few weeks ago:








The last picture is as of yesterday, as you can see it makes a HUGE difference. The next task for the porch is ripping the second floor deck off completely and rebuilding a smaller one that will match the porch below.

I refinished our porch swing using a red chestnut stain and 2 coats of poly. We picked it up at a thrift store last year for $20:


We got some new furniture for the living room. Sorry for the blurry pictures, it's time for a new camera:



It's all jammed against the wall for now because of the pool table. We're selling the table though so hopefully it should be gone soon.

That's all I have time to post for now. I'll try to make another post some some of the other work that's been accomplished in the morning.